How to use farm motor properly

1. The fuse motor must be installed in the motor circuit. During operation, it may be grounded due to burnout of the winding insulation, or a short circuit may occur due to the collision of the terminals. In order to protect the power supply and quickly eliminate short-circuit faults, fuses must be installed in the motor circuit 2 . The rated current of the fuse can be 2.5 to 3 times the rated current of the motor. In this way, when the motor is over-spending, the fuse is not easily blown, and when a short-circuit fault occurs in the circuit, the fuse can be quickly blown to protect the motor. In certain heavy-duty overloaded electric circuits, the value of the rated current of the fuse can be increased by a large amount, which can effectively reduce the phase failure of the fuse (that is, the fuse blows a phase and causes a single-phase operation. The winding is burned out, but still has enough short-circuit protection. 2. Pay attention to the temperature change when the motor is running. If the motor temperature does not exceed the maximum allowable temperature of the insulation material used, the insulation material has a long life of more than 20 years; if the temperature exceeds the maximum allowable temperature, the insulation material will be aged and become brittle. While shortening the service life of the motor, the insulation material will be carbonized and changed in a serious manner to promote the insulation performance and cause the motor to burn out. Therefore, during the operation of the motor, if it is found that the motor temperature exceeds the maximum temperature, it shall immediately stop the inspection to avoid burning the motor. In addition, if it is found that the temperature of the motor is much lower than the maximum temperature, the load is too small, and the load can be increased or replaced with a low-power motor. 3. Correctly selecting the power of the motor If the power is selected too much, it will cause waste and increase investment, and because the motor is often in a low-load operation, the efficiency and electric power are reduced, resulting in a decline in economic efficiency. Conversely, if the power selection is small, the motor will run overloaded, causing the speed to decrease and the temperature to rise, causing premature motor damage. Therefore, choosing the right power motor can improve the economic efficiency and prolong the service life of the motor.

Introduction
FT-C08 is a handhold Ambulatory Blood Pressure Monitor which is designed according to oscillography principle and could 24 hours ambulatory monitor NIBP.It supplies the exact   estimation warrant, and applies to clinique, the hospital wards or family daily health care.

 

Features
Compact and portable,friendly interface, easy to use
24 hours ambulatory NIBP measure function,at best 358 pieces of ambulatory NIBP measure data can be recorded once.
Automatic measure and manual measure of the perfect combination,at best 99 pieces of NIBP measure data can be recorded once by manual measure.
High-definition color TFT display, strong visibility
The device can display low power prompt information, alarm information, error information and time information richly
Communicate with PC,PC software can achieve data review, analysis measure results,seeing trend graph, printing reports and other functions

 

Performance
NIBP          
Measure Method: Oscillometry
Measure Mode: The upper arm measure
Automatic Measure Interval: 15.30.60.120,240 minutes
Measure range: 0kPa(0mmHg)~37.57kPa(280mmHg)
Accuracy:  ±3mmHg
Pulse Rate   
Measure range:40bpm~240bpm
Resolution:1bpm
Alarm parameter: SYS / MAP / DIA
Power: DC 3V(Two "AA",1.5V Alkali Battery)
Product safety type:Type BF applied part (Internally powered,defibrillation-proof)

Physics speciality
Dimension: 106mm*75mm*31 mm (No including Packing)
Weight: <137g (Including Batteries)

Accessories
Cuff for adult
Disk (PC software)
User manual
USB data line
Pack

Software function
PC software is connect to the device by USB interface
Can download NIBP measure result of the terminal device
Can display scoop-shape trend graph,filling-type trend graph, histogram, pie chart, correlation line graph.
Can edit every piece of NIBP data, and add annotation to it.
Can edit basic information,doctor's advice information, NIBP status instruction, current medicine-taken information, etc.
Support print preview,print the report.

ABPM

Ambulatory Blood Pressure Monitor,Ambulatory Blood Pressure Meter,Ambulatory Blood Pressure Monitoring,24 Hour Blood Pressure Monitor

Changchun Yingwang Times Digital Co., Ltd. , https://www.ccsdsm.com